Skip navigation and jump to the content

Products

H&K Behälter- und Edelstahltechnik GmbH
The experts for individual tanks and special designs.

Info:

References

Satisfied customers are the best proof for good work. We are very proud of a large number of existing customers that choose us time and again due to our high quality. Here you will find a selection of references from different industrial sectors.

Heatable mixing tank

Project information

Dimensions: Ø 2,000mm, total height 4,200mm, total capacity 6,600 l in jacket and cone area with double jacket divided in two zones and built-in spiral baffle. Interior with additional, removable heating jacket. The special challenge this project presented was the limited available space on site thus requiring high construction effort. The 45-kW agitator with buffer fluid system was also specially designed to meet the given possibilities.

Materials:

  1. Parts in contact with the product and outer double jacket made of 1.4571
  2. Supporting brackets made of 1.4301
  3. Tank flanges DN 2000 made of S235 JRG 2, plated with 1.4571

Surface treatment:

  1. Inner and outer surfaces pickled and passivated

Operating data:

  1. The tank has been designed for a maximum operating pressure of -1/ +6 bars in the interior and 4 bars in the outer and inner heating jacket, at 350 °C each. Acceptance according to PED (Pressure Equipment Directive) 97/23/EG, cat. IV, module G.

Info:

References

Satisfied customers are the best proof for good work. We are very proud of a large number of existing customers that choose us time and again due to our high quality. Here you will find a selection of references from different industrial sectors.

Mixing tank 132 l

Project information

Dimensions: Ø 500mm, total height 1,255mm. At the bottom with conical bottom, at the top with circumferential ring and screwed-on traverse sheet in the centre. Laterally with two flap cover parts. The agitator being part of the scope of supply consists of a compressed-air motor drive with rotation speed control.

Materials:

  1. Tank made of 1.4301/1.4541
  2. Wheels made of conductive socover rubber with polyamide rim

Surface treatment:

  1. Inner surfaces including welding seams ground up to grain size 400 and electropolished (Ra < 0,25μ)
  2. Outer surfaces (excluding welding seams) ground up to grain size 400

Operating data:

  1. The tank is designed for pressureless operation at 50 °C max.
  2. Acceptance by H&K

Info:

References

Satisfied customers are the best proof for good work. We are very proud of a large number of existing customers that choose us time and again due to our high quality. Here you will find a selection of references from different industrial sectors.

Mixing tank for 22,000 l

Project information

Diameter 2,450mm, total height including agitator ((without picture) 6,400mm. In the bottom and jacket area with double jacket and built-in spiral baffle. In the area of the double jacket insulated with 25mm mineral wool and coated with a tightly welded sheet jacket. Bottom of the insulation coating above a torospherical head as a cone. In the interior with welded-in bottom guidance bearing for the agitator shaft. Agitator (included in the scope of supply) with 7.5-kW with bevel gear motor and reinforced bearing as well as a frequency converter to be included in the electrical cabinet.

Materials:

  1. Tank completely made of 1.4301
  2. Insulation material: mineral wool

Surface treatment:

  1. Inner welding seams ground flush with the sheet surface
  2. Inner and outer surfaces completely pickled and passivated

Operating data:

  1. The tank is designed for pressureless operation at 50 °C max.
  2. Acceptance by manufacturer

Info:

References

Satisfied customers are the best proof for good work. We are very proud of a large number of existing customers that choose us time and again due to our high quality. Here you will find a selection of references from different industrial sectors.

Mobile tank with agitator

Project information

Dimensions: Ø 630mm, total height 1,000mm, total capacity 250 l. At the bottom with one-sided conical bottom, at the top with welded, planar segment cover with ¼ cut-out. Also included in the scope of supply: 0.37-kW agitator with built-on frequency converter; two heating devices to be screwed on with 5-kW; one drum pump for almost complete emptying of the barrel

Materials:

  1. Parts in contact with the product made of 1.4571, outer parts made of 1.4301
  2. Supports made of polyamide

Surface treatment:

  1. Inner and outer surfaces ground up to grain size 320
  2. Inner welding seams ground flush with the sheet surface
  3. Subsequently electropolished inside and outside

Operating data:

  1. The tank is designed for pressureless operation at 50 °C max.
  2. Acceptance by manufacturer

What's Next?

We roused your interest and you need an individual information or an expert advice. Call us now on + 49 78 51 70 89 68 – 0 .
Or contact us via skype on: status

For a request without obligation download our request template here.